- New



Seal4Go.Com One Stop Sealing Solution
Seal4Go.Com One Stop Sealing Solution
SCHNIEDER Oil Seal 0.875x1.500/2.500x0.500 M/L LEATHER is a specialized inch-size industrial rotary shaft seal featuring a dual outside-diameter designation of 1.500/2.500 inches. The manufacturer-specific M/L construction uses a genuine oil-treated industrial leather sealing element with metal support, making it suitable for lubricated shaft applications, bearing housings, gearboxes, transmissions, and legacy machinery originally designed for this specialized seal geometry.
The SCHNIEDER Oil Seal 0.875x1.500/2.500x0.500 M/L LEATHER is intended for rotary shaft applications around a 0.875-inch shaft.
Its dimensional designation includes two outside diameters:
This normally indicates a specialized outside profile rather than a conventional single-OD oil seal. However, the dimensions alone do not establish whether the larger diameter represents a flange, shoulder, retaining section, carrier, or another structural feature.
The exact relationship between the 1.500-inch and 2.500-inch outside diameters, including axial position, shoulder depth, carrier geometry, and installation method, must therefore be checked against the original SCHNIEDER seal or technical drawing.
The seal uses an industrial leather sealing element supported by a metal case or structural carrier. Properly conditioned and lubricated leather can conform to the shaft surface and tolerate minor surface irregularities, making this type of seal useful in older gearboxes, transmissions, agricultural machinery, and legacy industrial equipment.
The M/L profile is manufacturer-specific. Exact leather-lip geometry, support structure, outside-case arrangement, lip orientation, and installation direction should be verified before replacement.
Leather sealing elements should generally not operate dry. Adequate lubrication is important to minimize friction, heat generation, leather hardening, glazing, and premature wear.
Typical compatible lubricant/service environments include:
The inch dimensions convert approximately to:
Shaft diameter: 0.875 inch or 22.23 mm
Outside diameter designation: 1.500 / 2.500 inches or 38.10 / 63.50 mm
Seal width: 0.500 inch or 12.70 mm
Because of the unusual 1.500/2.500-inch dual-OD designation, the original cross-section should be confirmed carefully before ordering or installation.
⚙️ Applications
🎯 Benefits
✔ Genuine industrial leather sealing element
✔ Suitable for lubricated rotary shaft applications
✔ Can accommodate minor shaft-surface irregularities
✔ Suitable for 0.875-inch shaft assemblies
✔ Specialized dual-OD dimensional configuration
✔ Metal-supported M/L construction
✔ Well suited to legacy-equipment maintenance
✔ Suitable for slow-to-moderate speeds when properly lubricated
✔ Replacement ready when the full cross-section matches
🧠 Technical Insight
✅ Key Features
📊 Specifications
Brand: SCHNIEDER
Model / Profile: M/L
Size: 0.875 × 1.500/2.500 × 0.500 inch
Metric Equivalent: Approximately 22.23 × 38.10/63.50 × 12.70 mm
Type: Specialized Leather Rotary Shaft Oil Seal
Material: Genuine Oil-Treated Industrial Leather
Profile: M/L
Construction: Manufacturer-Specific Metal-Supported Leather Shaft-Seal Construction with Dual Outside-Diameter Designation
Lip Design: Leather sealing lip; verify exact M/L lip geometry and orientation against the original seal or technical drawing
Dust Lip: Not assumed; verify from the actual M/L construction
Spring Type: No spring unless the original seal specifically indicates one
Shaft Diameter (ID): 0.875 inch / 22.23 mm
Outside Diameter 1: 1.500 inch / 38.10 mm
Outside Diameter 2: 2.500 inch / 63.50 mm
Width: 0.500 inch / 12.70 mm
Outside Profile: Dual-OD / differential outside-diameter designation; verify whether the larger diameter represents a flange, shoulder, carrier, or other structural feature
Pressure Capability: Primarily low-pressure rotary shaft-sealing service unless otherwise specified
Lubrication: Oil or grease lubrication is generally required; leather should not normally operate dry
Temperature Range: Depends on leather grade, lubricant, shaft speed, and actual operating conditions
Speed Consideration: Generally best suited to slow-to-moderate shaft speeds with adequate lubrication
Installation Consideration: Verify both outside diameters, their axial relationship, installation depth, shoulder or flange geometry if present, shaft finish, housing geometry, lip orientation, and lubrication before fitting
Application Class: Specialized Industrial and Legacy Rotating Equipment
Standard: Inch-Size Specialized Leather Shaft Seal
🔁 Equivalent
Suitable replacement or cross-reference candidate for compatible:
The same shaft diameter, outside diameters, and width alone do not guarantee interchangeability. The replacement must match the original M/L cross-section, exact relationship between the 1.500-inch and 2.500-inch outside sections, leather-lip geometry, metal support structure, axial shoulder/flange geometry if present, installation direction, and operating requirements.
(Always verify the complete 0.875 × 1.500/2.500 × 0.500-inch cross-section against the original seal or drawing before ordering.)
📦 Availability
✅ In Stock
🚚 Fast Delivery Available
🌎 Worldwide Shipping Available
📦 MOQ: 1 Piece
🏭 Suitable for specialized bearing-housing repair, gearbox overhaul, transmission servicing, agricultural-machinery maintenance, legacy-equipment restoration, and OEM replacement applications requiring the same M/L and dual-OD construction.
📲 Contact via LINE ID: dusitrea
📧 Email: sales@seal4go.com
💬 Technical support available before ordering
🔍 Assistance available for cross-reference and equivalent part identification
Data sheet
Specific References
No customer reviews for the moment.