

Seal4Go.Com One Stop Sealing Solution
Seal4Go.Com One Stop Sealing Solution
MRC (SKF) 213SFF is a single-row deep groove radial ball bearing from the traditional MRC 200-S Series.
Basic dimensions:
Bore: 65 mm
Outside Diameter: 120 mm
Width: 23 mm
This dimensional envelope corresponds to the modern 6213 bearing family.
The S designation identifies the standard non-filling-slot deep-groove construction, while the FF suffix in this MRC family is generally associated with a double-side protected / typically double metal shielded configuration.
The MRC 213SFF is a single-row deep groove ball bearing designed primarily for radial loads while also accommodating moderate axial loads in both directions.
Its standard mounting dimensions are:
65 × 120 × 23 mm
which correspond dimensionally to:
6213
The bearing uses a conventional:
Non-Filling-Slot / Conrad-Type Deep Groove Construction
This differs from MRC M-series maximum-capacity bearings, which use filling slots and a larger ball complement for greater radial load capacity.
The FF protected execution helps retain grease and reduce the entry of dust and larger contaminants while maintaining relatively low friction compared with contact rubber-sealed bearings.
⚙️ Applications
🎯 Benefits
✔ Standard 65 × 120 × 23 mm dimensions
✔ Single-row deep groove construction
✔ Non-filling-slot / Conrad-type design
✔ Good radial-load capability
✔ Supports moderate axial load in both directions
✔ Double-side protected configuration
✔ Good grease retention
✔ Lower friction than typical contact rubber-sealed bearings
✔ Modern 6213-series replacement options widely available
🧠 Technical Insight
✅ Key Features
📊 Specifications
Brand: MRC (SKF)
Model / Bearing Number: 213SFF
Base Bearing: MRC 213S
Series: MRC 200-S Series
Modern Dimensional Reference: 6213
Product Type: Deep Groove Ball Bearing
Bearing Type: Single-Row Radial Ball Bearing
Construction: Non-Filling-Slot / Conrad-Type
Bore Diameter (d): 65.00 mm
Outside Diameter (D): 120.00 mm
Width (B): 23.00 mm
Rolling Elements: Ball
Number of Rows: 1
Primary Load: Radial
Axial Load Capability: Moderate axial load in both directions depending on operating conditions
Closure: Protected on both sides
FF Suffix: Typically associated with double-side shielding / protection in this MRC family; verify the actual bearing if exact closure construction is critical
Lubrication: Normally grease-retaining protected-bearing configuration
Internal Clearance: Not defined by the basic 213SFF designation; verify Normal, C3, or another clearance if required
Cage: Verify original MRC production specification
Dynamic Load Rating: Verify original MRC or exact replacement manufacturer data
Static Load Rating: Verify original MRC or exact replacement manufacturer data
Speed Rating: Depends on shield construction, grease, internal clearance, fits, temperature, and load
Shaft Fit: Nominal 65 mm shaft
Housing Fit: Nominal 120 mm bearing seat
🔁 Equivalent
Suitable dimensional replacement or cross-reference candidates include:
The dimensional relationship is:
MRC 213SFF = 65 × 120 × 23 mm
which corresponds to:
6213
If the original FF execution is confirmed as double metal shielded, the closest modern constructional family is:
6213-2Z / 6213ZZ
depending on manufacturer terminology.
Both can share:
65 × 120 × 23 mm
but differ in closure.
MRC 213S
MRC 213SFF
Therefore, even when dimensions are identical, the bearings can differ in:
Both commonly share:
65 × 120 × 23 mm
but use different closure systems.
6213-2Z / ZZ
6213-2RS / 2RSH / 2RS1
Therefore, 6213-2RS should not automatically replace MRC 213SFF solely because the dimensions match.
Before replacing MRC 213SFF, verify:
(Always verify the full marking and actual closure of the original MRC 213SFF before selecting SKF 6213-2Z, FAG 6213-2Z, NTN 6213ZZ, NSK 6213ZZ, or another replacement.)
📦 Availability
✅ In Stock
🚚 Fast Delivery Available
🌎 Worldwide Shipping Available
📦 MOQ: 1 Piece
🏭 Suitable for electric motors, pumps, fans, gearboxes, conveyors, rollers, agricultural machinery, processing equipment, and general industrial machinery requiring a 65x120x23 mm double-side protected deep groove ball bearing.
📲 Contact via LINE ID: dusitrea
📧 Email: sales@seal4go.com
💬 Technical support available before ordering
🔍 Assistance available for cross-reference and equivalent part identification
Data sheet
Specific References
No customer reviews for the moment.